If rubber-base paint has been used, the caustic soda treatment may not be effective and it may be necessary to use an organic solvent type of paint remover. Caution: - When using caustic soda or lye, avoid splashing eyes, skin, and clothing. Note: How to use an airless paint sprayer. I'm sure the guy at the rental store showed you how to use the airless (typically with his limited experience of actually painting a house), so hopefully I can offer you a couple new ideas on how to paint your home using an airless paint sprayer. When you first get the airless home, set it in the middle of the area that you would like to start painting. Typically the length of the hose is around 50'. Stretch out the hose prior to painting so that you don't have to worry about unraveling it while you are painting on a ladder. It is a good idea to have a 100' extension cord so that you can bring the airless anywhere you wish to paint without any restrictions. Tip: before you plug in the airless into the extension cord, MAKE SURE THE AIRLESS IS OFF! You don't want the airless to start pumping without paint! Now, when you go to set up the airless, before you turn it on, it's a good rule of thumb to have a second empty bucket next to your bucket of paint. I'll explain why in a second. Place both buckets side by side and place the intake hose (with the wire mesh filter end) into your 5 gallon bucket of paint while the primer hose (usually a lot smaller, about the size of a pencil'ish) is placed in the empty bucket of paint. Before you turn on the machine make sure that the airless is set to prime the machine first. There is a primer valve that you can rotate between prime and paint. A good way to see if the valve is set to prime or paint is to try this little test prior to turning the machine on. While turning the valve clockwise a couple times you will notice that the valve handle will separate from the machine in one position (leaving a slight crack between the valve and machine) while the other position the valve is close to the machine. The position in which the valve is separated from the machine is considered the primer position. Do this multiple times to see what I'm talking about. Don't worry if you keep on spinning the valve, you can spin it a million times in one direction and it won't hurt it. What colors are prevailing - tonal or local, warm or cold?
Building a monochromatic theme simply uses a single color in graduating shades like cream, beige and brown. It is hard to go wrong with this color palette, so everyone can use it successfully. But unless variations of the one color used are handled with flair, this can be an unexciting look. Materials and their application, every paint manufacturers paint will vary. If you are freshening up old walls and painting back to the existing color, the product doesn't have to be high end or have good coverage. If you need to paint a dark color over light color or light color over dark, you may want to consider purchasing a top quality paint to avoid multiple coats. I suggest Valspar, Pittsburgh or Benjamin Moore top of the line wall paint. These brands work well for straight out of the bucket use and are application friendly. Sherwin Williams is not my first choice because the coverage is poor and you will have to apply multiple coats but, it does apply, fluently. If you find a product does not apply well, maybe it is to heavy and/or sagging on the wall, you may need to thin the paint with a little water, this will reduce the coverage but make the paint flow better and lay down nicer on the surface. I do recommend latex paints for all applications, these days a good high end latex is as good as oil paint and your tools clean up much easier, it will also be less harsh on the respiratory system. The only situation I recommend oil paint, is as a primer/stain blocker over stains that "bleed" through the paint. You can get a stain blocking oil primer in a convenient spray can and spot prime any trouble areas before painting and in the case you need to prime all of the wall due to smoke or water damage, I recommend getting it in gallons and rolling it on where the stains are present. Don't forget proper ventilation and/or a respirator when using the oil based primers! INTERIOR PAINTING. If you want to alter your room's ambience, painting it is a great option. When interior painting, use paints that are quicker to dry and does not have a strong odor that lingers around where your kids can smell it. And if you are changing colors be sure you and the paint shop are crystal clear on what color they're going to spray. Never just describe the color. You won't get what you want. Guaranteed. If you're not using a factory original color then find out what kind of car the color you want came on. Give the shop a year, model and paint name and then insist on seeing a paint chip. Take the chip outside to see it in the sun light and verify that it's what you want. There's nothing more disappointing then spending all these hours and money only to watch your car come out of the shop the wrong color.