Valspar Paint, for instance, also produces paint branded as Laura Ashley, Eddie Bauer, Waverly, and more. These separate lines, or collections, have their own color wheel displays and are usually available wherever the primary brand, Valspar in this case, are sold. Other examples are Disney Paints, currently produced by Behr, and Ralph Lauren and Martha Stewart, formerly produced by Sherwin Williams. Limewash - Made from slaked lime and water, this paint is good for porous surfaces such as brickwork, render and plaster and gives a chalky finish. It is available from specialist companies. Cold water paints of the casein type may be applied either directly to a plastered surface, or the surface may be first given a coat of primer-sealer to equalize uneven suction effects. The same is true of resin-emulsion paints, with the recommendations of the manufacturer of the product being given preference in case of doubt. Since resin-emulsion paints usually contain some oil in the binder, they should ordinarily be applied only to plaster which has dried thoroughly.
The second part of preparation is surface prep, it addresses covering the surfaces you do not want to get any paint on. A little plastic sheeting will go along way to keeping paint off of floors, window coverings, handrails, cabinets, counter tops, etc... And, if you are not confident with your ability to paint a straight line next to door casing, baseboards, cabinets or hardware protect these surfaces using masking tape. There are two basic types of masking tape white/yellow and blue. The white tape sticks to surfaces better but, can pull off finishes on cabinets or stained woodwork. Blue tape usually will not pull off finishes but, does not stick as well, this will probably be the tape to use for most applications. Always wipe down or dust the surface you will be masking to assure the best tape adhesion possible. If you use blue tape you may need to re-rub down the tape before painting next to it, only mask off areas with blue tape that you will be painting for a given day. With either tapes, do not assume the are a force field that paint will not penetrate, use them as a reference and dry brush the paint next to the edge of the tape and avoid soaking the edge of the tape with a lot of paint, this will cause the paint to "bleed" through giving you an undesired look. If you will need to apply multiple coats of paint, on the first coat, paint as close to the tape as you can, not really getting paint on the tape. With the second coat or a one coat application, you can use the tape more of like a paint barrier and get a little more paint on the tape if you immediately remove each section of tape after painting the section, this will keep the paint from sitting on the tape and "bleeding" behind it. Also, if you get a lot of paint on the tape it is not good to let the paint dry on the tape because some paints (especially the glossier paints) will peel if allowed to dried, with the tape when it is pulled off. White tape should not be left on for longer than a couple of days and I suggest not leaving it on more than a day in areas that receive long periods of direct sunlight. Blue tape can be left on for days, if it will stay on, there again it does not stick as well and may need rubbed down again immediately before painting up next to it. Airless Tip: If you have somebody who can start masking off the trim, have them start on that while you convert the airless to a new color. When changing colors with an airless paint sprayer it is a good idea to have a second bucket filled half way with clean water. Place the intake hose in the clean water gently without getting the old color everywhere in the water. Take the tip out of the airless and spray all of the old paint out of the hose and back into its original paint bucket. Be careful when doing this that you recognize when the paint starts turning watery. When it does point the gun into the first bucket and spray until it looks pretty clean. It doesn't need to be perfectly clean. When it looks good, clean off the intake line in the clean bucket and get the old color off the intake line. Now place the intake line inside of your new trim paint. When all of the spraying is complete, its time to remove all masking tape and paper and start touching up your entire home. This step is pretty time consuming because this is the final stage that really makes your home look good. The more time you spend here, the better your home will look. What emotions does it produce?