When it comes to rolling out the walls never ever use a cheap foam roller. Foam rollers never evenly absorb the paint out of the pan and will actually add time to you project and cause more mess. Buy yourself a synthetic professional 3/8 nap roller head for about $6 to $8. Not only will the paint be applied in a smoother fashion you will experience less work and mess. Paint & Paper Library arranges its colours in five shades from light to dark to help select coordinating colours for ceilings, cornices, walls, doors and woodwork. If you are decorating around bold furnishings, such as a sofa or curtains, look at paint colours from the same fabric house as they are most likely to be sympathetic. Note: How to use an airless paint sprayer. I'm sure the guy at the rental store showed you how to use the airless (typically with his limited experience of actually painting a house), so hopefully I can offer you a couple new ideas on how to paint your home using an airless paint sprayer. When you first get the airless home, set it in the middle of the area that you would like to start painting. Typically the length of the hose is around 50'. Stretch out the hose prior to painting so that you don't have to worry about unraveling it while you are painting on a ladder. It is a good idea to have a 100' extension cord so that you can bring the airless anywhere you wish to paint without any restrictions. Tip: before you plug in the airless into the extension cord, MAKE SURE THE AIRLESS IS OFF! You don't want the airless to start pumping without paint! Now, when you go to set up the airless, before you turn it on, it's a good rule of thumb to have a second empty bucket next to your bucket of paint. I'll explain why in a second. Place both buckets side by side and place the intake hose (with the wire mesh filter end) into your 5 gallon bucket of paint while the primer hose (usually a lot smaller, about the size of a pencil'ish) is placed in the empty bucket of paint. Before you turn on the machine make sure that the airless is set to prime the machine first. There is a primer valve that you can rotate between prime and paint. A good way to see if the valve is set to prime or paint is to try this little test prior to turning the machine on. While turning the valve clockwise a couple times you will notice that the valve handle will separate from the machine in one position (leaving a slight crack between the valve and machine) while the other position the valve is close to the machine. The position in which the valve is separated from the machine is considered the primer position. Do this multiple times to see what I'm talking about. Don't worry if you keep on spinning the valve, you can spin it a million times in one direction and it won't hurt it.
Now here comes the fun part doors and wood work. This is where most people opt to use latex which is a huge mistake. Your home is your biggest investment don't cut corners on it's aesthetics. You want the finish on your woodwork to stand out from the walls especially if you have crown moulding or waynes coating. Don't be fooled by water based products that claim to give the look and finish of oil. It's just good marketing preying on people's fears of painting with oil. Don't believe the hype as those samples they show you have 3 or 4 coats that have been professionally sprayed in a dust free environment. You will not get the same results I can promise you that. You have a choice of semi-gloss or gloss finish. I prefer gloss because to me it gives you a bit more durability and shine. Either one will be fine for your project. Now let's get started. Also, when checking the paint, be realistic and don't ignore areas just for the sake of convenience. It will cost you more in time and money later. Typically if one area of the paint is cracked or peeling, then the paint on the entire car is suspect. Maybe the rest of the car just hasn't quite reached that point of decay, but it will shortly. So if you only fix areas that look bad, you'll likely find that you wasted a paint job when the other areas start to crack or peel in a year or two. Playing fun games where word sounds are changed, learning silly rhymes and making up nonsense words helps children develop their phonics skills and auditory processing. If these are simply taught in a formal way, the child feels no real ownership and finds it harder to remember all the different sounds the written letters represent. If he plays games and experiments with the sounds in words, his feeling of being in control of the words and the sounds is greater, making it easier for him to learn and remember his phonics. He develops an actual concept of how sounds make up words. Once the drywall compound/spackle has had sufficient time to dry, you will need to lightly sand the surface of the repair to smooth out any ridges that may have been caused while "coating" the patch. Once you have the surface sanded smooth, take a wet sponge or cloth and, by lightly washing/rubbing, blend the outside edge of the drywall compound/spackle back into the wall. For a smaller repair, you can wash away the excess drywall compound, leaving only the compound/spackle only in the area where the indent was filled. For a larger hole, after filling, sanding and using a wet sponge to blend the outside edge of the compound back into the wall, it may be necessary to texture the area in order to give the smooth patch the appearance of the existing wall.