Paint should not be applied to a concrete basement floor until the concrete has aged for at least a year. The floor should be dry when painted, the best time for application being during the winter or early spring (assuming there is some heating apparatus in the basement), when the humidity in the basement is low. In general, three coats of paint are required on an unpainted floor, and the first coat should be thin to secure good penetration. After the paint is dry, it should be protected with a coat of floor wax. Note: How to use an airless paint sprayer. I'm sure the guy at the rental store showed you how to use the airless (typically with his limited experience of actually painting a house), so hopefully I can offer you a couple new ideas on how to paint your home using an airless paint sprayer. When you first get the airless home, set it in the middle of the area that you would like to start painting. Typically the length of the hose is around 50'. Stretch out the hose prior to painting so that you don't have to worry about unraveling it while you are painting on a ladder. It is a good idea to have a 100' extension cord so that you can bring the airless anywhere you wish to paint without any restrictions. Tip: before you plug in the airless into the extension cord, MAKE SURE THE AIRLESS IS OFF! You don't want the airless to start pumping without paint! Now, when you go to set up the airless, before you turn it on, it's a good rule of thumb to have a second empty bucket next to your bucket of paint. I'll explain why in a second. Place both buckets side by side and place the intake hose (with the wire mesh filter end) into your 5 gallon bucket of paint while the primer hose (usually a lot smaller, about the size of a pencil'ish) is placed in the empty bucket of paint. Before you turn on the machine make sure that the airless is set to prime the machine first. There is a primer valve that you can rotate between prime and paint. A good way to see if the valve is set to prime or paint is to try this little test prior to turning the machine on. While turning the valve clockwise a couple times you will notice that the valve handle will separate from the machine in one position (leaving a slight crack between the valve and machine) while the other position the valve is close to the machine. The position in which the valve is separated from the machine is considered the primer position. Do this multiple times to see what I'm talking about. Don't worry if you keep on spinning the valve, you can spin it a million times in one direction and it won't hurt it. A good interior paint job is often 50% preparation and 50% painting. Do not rush in preparing the surfaces in your eagerness to get at the brush or roller. If you do not prepare the surfaces properly, you'll be back with the paint brush or roller in a few months.
There is still no standard labelling scheme for paint. The blue globe label, pioneered by B&Q, led to VOC reduction on the mass market and has been adopted by other brands, while the European Ecolabel, recognised in 15 EU member states, looks like a flower and appears on brands such as Earthborn. Germany also has a Blue Angel label and there is a green Nordic Swan as well. You will find more detailed information on most of the paint company's websites, as well as a wealth of practical and design advice. If paints have been allowed to stand and hard lumps or skin have formed, the skin or scum should be removed, after which the paint can be stirred and strained through screen wire or through one or two thicknesses of cheesecloth. Airless Tip: If you have somebody who can start masking off the trim, have them start on that while you convert the airless to a new color. When changing colors with an airless paint sprayer it is a good idea to have a second bucket filled half way with clean water. Place the intake hose in the clean water gently without getting the old color everywhere in the water. Take the tip out of the airless and spray all of the old paint out of the hose and back into its original paint bucket. Be careful when doing this that you recognize when the paint starts turning watery. When it does point the gun into the first bucket and spray until it looks pretty clean. It doesn't need to be perfectly clean. When it looks good, clean off the intake line in the clean bucket and get the old color off the intake line. Now place the intake line inside of your new trim paint. Complementary colors are opposites, and if you look at a color wheel, they are directly across from each other. While complementary colors may seem kind of mysterious to a novice, you just have to bring to mind Christmas to find a great example that is familiar to everyone, red and green.By simply making these colors a little paler, you can make this color palette work really well. Color tones are important, because rust and moss, while still being red and green, do not scream 'Christmas'. If your choice of tones is bold, you will create an eye popping design. However, it is common to get off course.