Sailor Moon (美少女戦士セーラームーン, Bishōjo Senshi Sērā Mūn, originally translated as Pretty Soldier Sailor Moon and later as Pretty Guardian Sailor Moon ) is a Japanese shōjo manga series written and illustrated by Naoko Takeuchi. It was originally serialized in Nakayoshi from 1991 to 1997; the 60 individual chapters were published in 18 tankōbon volumes. The series follows the adventures of a schoolgirl named Usagi Tsukino as she transforms into Sailor Moon to search for a magical artifact, the “Legendary Silver Crystal” (「幻の銀水晶」, Maboroshi no Ginzuishō, lit. “Phantom Silver Crystal”). She leads a diverse group of comrades, the Sailor Soldiers (セーラー戦士, Sērā Senshi) (Sailor Guardians in later editions) as they battle against villains to prevent the theft of the Silver Crystal and the destruction of the Solar System.
Jodhpur School: The centre of this hand made paintings are love scenes then the other art figures. The Jodhpur School of Miniature paintings depict love scenes of lovers Dhola and Maru on camel back. There are hunting scenes with elephants and horses. The major colors used in this style of painting are gold and stone color. The term paint is used to include paints, varnishes, enamels, shellacs, lacquers, and stains. • Paints are composed of mineral pigments, organic vehicles, and a variety of thinners all combined. • Varnishes are resins dissolved in organic thinners. • Enamels are pigmented varnishes. • Shellac is lac gum dissolved in alcohol. • Lacquers may be both pigmented or clear - the liquid portion usually is treated nitrocellulose dissolve in thinners. • Stains may be pigmented oil or a penetrating type. Many of these materials, such as paints, varnishes, and lacquers, are formulated for specific purposes: • Outside house paints and exterior varnishes are intended to give good service when exposed to weathering • Interior wall paints are formulated to give excellent coverage and good wash-ability. • Floor enamels are made to withstand abrasion. • Lacquers are formulated for rapid drying. • There are also formulas which provide extra self-cleaning, fume- resisting, waterproofing, hardening, flexibility, mildew-resisting, resistance to fading, and breathing qualities. "Boxing" is a good method of mixing paints. Since paint is a mixture of solids and liquids, it is important that it be mixed thoroughly before using. To do this, the greater portion of the liquid contents of the can should be poured in a clean bucket somewhat larger than the paint can. Then, with a stiff paddle, the settled pigment in the original container should be loosened and any lumps broken up. After this, mix the material in the container thoroughly, using a figure 8 motion, and follow with a lifting and beating motion. Continue stirring the mixture vigorously while slowly adding the liquid that was previously poured off the top. Complete the mixing by pouring the paint back and forth from one container to the other several times until the entire amount is of uniform consistency.
When you plan with split complementary colors, you begin with a single reference color. Next, choose a color from either edge of the complementary color and use it. While the complementary color scheme is a little more obvious, this scheme can fail totally if you just use paler versions of your warm colors. By the same token, picking a a warm undertone for the main contrasting color and combining it with two cool tones will showcase the warm tone. You can tell when the bucket of paint is getting low when the airless starts pumping really loud and doesn't stop. Simply tip the nearly empty bucket of paint, at an angle so that the mesh filter is covered and wait for the airless to catch up and stop pumping. Sometimes it's just easier to just to replace the bucket of paint with the new one and when that starts going down, pour the excess from the old bucket into the new one. Color - The paint makers are out to sell the lady of the house and color is their come-on. They are tempting her with a kaleidoscope's variety; one firm offers more than 6,000 different shades. Once you figure out which position is prime and which position is spray, place the valve in the prime position and grab the primer hose. Point the primer hose in the empty bucket near the top and at an aproxx.45 degree angle from the side (the reason for this is that there is likely to be pressure still built up in the airless and when you first switch on the airless to prime it, paint will likely burst out of the primer hose and you don't want to have it go everywhere). Now turn the airless paint sprayer on and you will see that the airless is sucking up the new paint and pumping out the primer hose. At first you will typically see a cleaning solution come out followed by your paint. When you see your paint coming out switch over the primer valve to the other position and you will see the airless pumping paint into the main hose.